Build your own Home Assistant Base System!

Home Assistant is an Open source home automation system that puts local control and privacy first. Powered by a worldwide community of tinkerers and DIY enthusiasts, the Home Automation "Build Your Own" bundle allows for control of all your compatible household devices from the app on your phone. Think Apple Homekit, but better.

NOTE - CASES, POWER SUPPLIES, AND EMMC CARDS SELECTABLE TO THE RIGHT ARE CURRENTLY AVAILABLE - (Blue Aluminium Case is a modified version of M1 Case Kit)

Getting started is as easy as plugging in the network and power cables and opening up the Home Assistant mobile app to get started.

Reliable

The ODROID N2+ (4GB RAM) with Home Assistant Bundle comes with an eMMC storage. Plenty of space for all your integrations.

Resilient

The ODROID N2+ (4GB RAM) with Home Assistant Bundle has a sturdy metal case designed by us - which will keep your system safe, secure, and well ventilated.

Open source

All software that runs on ODROID N2+ (4GB RAM) with Home Assistant Bundle is open source using the Linux kernel - including all the hardware drivers!

What’s in the bundle (Some parts are optional)

• Choice of Case
• ODROID N2+ with 4GByte RAM
• eMMC Card storage with Home Automation pre-installed (choice of sizes)
• RTC backup battery
• Power adapter (12V/2A) (UK Or EU Version Available)

ODROID N2+ (4GB RAM) with Home Assistant is future proof

The ODROID N2+ (4GB RAM) with Home Assistant Bundle is powered by a powerful processor, solid amount of RAM memory and comes with a comfortable amount of storage.It allows you to easily run the Home Automation app, a couple of add-ons and then a couple more. It will be able to easily integrate thousands of devices and run thousands of automations.

Form Factor	Dimensions: 140mm x 95mm x 40mm approximately. Weight: 300g including heatsink and metal case
Processor	Amlogic S922X Processor (12nm fab)  Quad-core Cortex-A73(up to 2.4Ghz) and Dual-core Cortex-A53 (up to 2Ghz) ARMv8-A architecture with Neon and Crypto extensions Mali-G52 GPU with 6 x Execution Engines (800Mhz)
Memory	DDR4 4GB with 32-bit bus width.  Data rate: 2640 MT/s (PC4-21333 grade) 1.2Volt low power design
Storage	1 x eMMC connector 1 x microSD slot (DS/HS modes up to UHS-I SDR104) - eMMC cARD Preinstalled
Networking	1 x GbE LAN ports (RJ45, supports 10/100/1000 Mbps)– Realtek RTL8211F (Ethernet transceiver) – LED indicators * Green LED: Flashing by data traffics at 100Mbps connection * Amber LED: Flashing by data traffics at 1000Mbps connection Optional WiFi USB adapters
Video	1 x HDMI 2.0 (up to 4K@60Hz with HDR, CEC, EDID)
Audio	1 x Stereo Audio line-out (3.5mm jack) 1 x HDMI digital output 1 x Optional SPDIF optical output
External I/O	4 x USB 3.0 Host ports (shares one single root hub)  1 x USB 2.0 OTG port for Host or Device mode. (No power input) 1 x Debug serial console (UART) 1 x Peripheral Expansion Header (40-pin, 2.54mm pitch) – 2 x DC 5V, 2 x DC 3.3V, 1 x DC 1.8V, 8 x GND – 1 x SPI – 1 x UART – 2 x I2C – 25 x GPIO (Max) – 2 x ADC input (10bit, 1.8V Max) – All 3.3V I/O signal level except for ADC input at max 1.8Volt.
Other features	On board RTC(Real Time Clock) IC keeps time up to several years with a preinstalled CR2032 battery. 8MiB SPI Flash for boot manager IR receiver for remote controller Built with a large passive heatsink System LEDS Indicators: – Red (PWR) – Solid light when DC power is connected – Blue (ALIVE) – Flashing like heartbeat while Kernel is running. Active Cooling Fan Connector (5V 2-pin) – Connector (2-pin, 1.25mm pitch)
Power	1 x DC jack : outer (negative) diameter 5.5mm, inner(positive) diameter 2.1mmDC 7.5V ~ 18V (up to 25W) – DC 12V/2A power adapter is included Power consumption: – IDLE : ≃ 2.2W (Performance governor) – CPU Stress : ≃ 5.9W (@2016/2208MHz), 6.2W (@2016/2400MHz) – Power-off : ≃ 0.2W